It's a Ronnefeldt tilting teapot.

We've got a conveyor there.

Those are conveyor belts that go around.

Or it will be tilting towards the Sun.

like a conveyor belt running in two directions.

You can operate the chip conveyor in Setup mode but you must press and hold the conveyor key CHlP FWD

Connect the Electrical Cable to the receptacle labeled Conveyor

It's all conveyor belt, and it makes a book.

Ask someone to assist you to hold the weight of the Chip Conveyor while you unfasten the Shipping Security Screws and lower the Conveyor into position

And if you think the tilt is tilting us closer, no, it isn't.

The Sun is 93 million miles away, and we're tilting like this, right?

Route the Electrical Cable neatly from the Conveyor Motor down to the receptacle

Ah, ah! There it is. It's picked up the object off the conveyor.

It has also two tilt sensors that tell the machine which way it's tilting.

If a Chip Guide Bracket is included with the Conveyor Accessories, install it now

Move to the Belt Tensioning Bolts and tighten them inwards towards the Conveyor Motor

With electricity supplied to the Conveyor press the CHlP FWD key to make sure the Conveyor Belt feeds smoothly with no binding or dragging inside the Enclosure and at the Chip Discharge Point

I can speed up the whole sequence by tilting the tempo one way or the other.

Weatherstaff's robin redbreast, tilting forward to look at her with his small head on one side.

Connect both coolant pump power cables as well as the power cable for the chip conveyor

Along the conveyor belt, packets of data are coming in and going out of your computer.

Once installed push the Conveyor back in towards the center of the Machine until it is fully seated

If you keep kind of tilting if you start with a circle, tilt a little bit, you get an ellipse.

With the conveyor lowered install the Bracket Screws back into the holes they came from on the Enclosure Side Panel

This is one of the conveyor belts with the thing going by, but then you'll see the ones up above.

If we keep tilting this plane, so if we tilt the plane so it's so let's say we're pivoting around that point.

And then, if you keep tilting this plane, and I'll do it another color so it intersects both sides of the cone.

Note that any chip conveyor support screws or brackets should not be touching the ground until after the leveling procedure is complete

The robin kept singing and twittering away and tilting his head on one side, as if he were as excited as she was.

Once settled, move the turret back across full Z axis travel to the spindle side and note which direction the level is tilting

Start with the screws on the chip conveyor side followed by two of the four screws on the left side of the panel

Remove the four Screws connecting the Conveyor Shipping Brackets to the Machine Enclosure and carefully lower the section until it is set in the installed position

I should have done that in yellow. So on my asset side of the balance sheet it's just strangely tilting to the left On the asset side, I actually have 1000 gold pieces

And to visualize that, just imagine tilting this line, and as you take different, so it looks like its the case over there, if you take the line like this and you look at it over here, it's clear that this is equal to this and there's actually no proof for this.

Because of the Earth tilting on its axis and those catastrophic climate shifts, we had to figure out how to find better food, and we had to learn there's Lucy that's how we all began we had to learn how to crack open animal bones, use tools to do that, to feed on the marrow, to grow our brains more.

So remember, this tilt, the direction this arrow points into relative the rest of the universe, if we assume that this tilt, that 23,4 , it's not changing throughout the year, but depending on where it is in the orbit, it's either going to be tilted away from the Sun, as it is in this example right over here, or it will be tilting towards the Sun.